VALÍČEK, Jan, Marta HARNIČÁROVÁ, Milena KUŠNEROVÁ, M. ŠAJGALÍK, Ján KMEC, I. KOPAL, A. PANDA a Zuzana PALKOVÁ. Reverse reconstruction of surface topography from residual stress after chip-forming machining of the material. Materialwissenschaft und Werkstofftechnik. Německo: Wiley-VCH Verlag, roč. 51, č. 5, s. 579-585. ISSN 0933-5137. doi:10.1002/mawe.202000017. 2020.
Další formáty:   BibTeX LaTeX RIS
Základní údaje
Originální název Reverse reconstruction of surface topography from residual stress after chip-forming machining of the material
Název česky Reverzní rekonstrukce povrchové topografie ze zbytkového napětí po třískovém obrábění materiálu
Autoři VALÍČEK, Jan (203 Česká republika, garant, domácí), Marta HARNIČÁROVÁ (203 Česká republika, domácí), Milena KUŠNEROVÁ (203 Česká republika, domácí), M. ŠAJGALÍK (703 Slovensko), Ján KMEC (203 Česká republika, domácí), I. KOPAL (703 Slovensko), A. PANDA (703 Slovensko) a Zuzana PALKOVÁ (703 Slovensko, domácí).
Vydání Materialwissenschaft und Werkstofftechnik, Německo, Wiley-VCH Verlag, 2020, 0933-5137.
Další údaje
Originální jazyk angličtina
Typ výsledku Článek v odborném periodiku
Obor 20301 Mechanical engineering
Stát vydavatele Německo
Utajení není předmětem státního či obchodního tajemství
WWW URL
Kód RIV RIV/75081431:_____/20:00001756
Organizační jednotka Vysoká škola technická a ekonomická v Českých Budějovicích
Doi http://dx.doi.org/10.1002/mawe.202000017
UT WoS 000532585700005
Klíčová slova česky Zbytkové napětí; drsnost povrchu; třískové obrábění; deformace; mechanické vlastnosti
Klíčová slova anglicky Residual stress; surface roughness; chip-forming machining; deformation; mechanical properties
Štítky CHS, RIV20, SCOPUS, WOS
Změnil Změnila: Kateřina Nygrýnová, učo 23736. Změněno: 5. 6. 2020 08:20.
Anotace
Residual stress is induced in the sample of a material stressed by external forces (tension, pressure, thermal stress, etc.) from the beginning of the stress. An instantaneous level is a function of the intensity of the external deformation work, the time and speed of the deformation, and the degree of immediate surface and volume deformation. It is proportional to the individual deformation limits, i. e., the elastic limit, yield point, flexural strength and breach limit; the maximum is reached at the level of the breach limit. Furthermore, it is dependent on the physical-mechanical properties of the material and on the method, i. e., the technology of straining, or machining. The same applies to the roughness distribution and other topographical features on the machined surface. The tension that has not been exhausted is partly returned to the volume of the sample and partly acts in contact with space, within a certain distance and time. This paper aims to present a reverse reconstruction of the surface topography from residual stresses after chip-forming machining of the material. Our original approach to the solution fully exploits the rules of roughness distribution and other topographic features of the surfaces of the given materials after machining, not only by chip-forming machining.
Anotace česky
Zbytkové napětí je indukováno ve vzorku materiálu namáhaného vnějšími silami (napětí, tlak, tepelné napětí atd.) Od začátku napětí. Okamžitá úroveň je funkcí intenzity vnější deformační práce, času a rychlosti deformace a stupně okamžité deformace povrchu a objemu. Je úměrná individuálním limitům deformace, tzn. e. mez pružnosti, mez kluzu, pevnost v ohybu a mez porušení; maximum je dosaženo na úrovni limitu porušení. Dále je to závislé na fyzikálně-mechanických vlastnostech materiálu a na způsobu, tzn. např. technologie napínání nebo obrábění. Totéž platí pro rozdělení drsnosti a další topografické znaky na obrobené ploše. Napětí, které nebylo vyčerpáno, je částečně vráceno do objemu vzorku a částečně působí v kontaktu s prostorem, v určité vzdálenosti a čase. Tato práce si klade za cíl představit reverzní rekonstrukci povrchové topografie ze zbytkových napětí po obrábění materiálu na třísky. Náš původní přístup k řešení plně využívá pravidla distribuce drsnosti a dalších topografických rysů povrchů daných materiálů po obrábění, nejen pomocí třískového obrábění.
VytisknoutZobrazeno: 28. 3. 2024 13:22