J 2023

Effect of Topology Parameters on Physical–Mechanical Properties of Magnetic PLA 3D-Printed Structures

ZÁRYBNICKÁ, Lucie; Marek PAGÁČ; Radek ŠEVČÍK; Jaroslav POKORNÝ; Martin MAREK et al.

Basic information

Original name

Effect of Topology Parameters on Physical–Mechanical Properties of Magnetic PLA 3D-Printed Structures

Name in Czech

Vliv topologických parametrů na fyzikálně-mechanické vlastnosti magnetických 3D tištěných struktur z PLA

Authors

ZÁRYBNICKÁ, Lucie; Marek PAGÁČ; Radek ŠEVČÍK; Jaroslav POKORNÝ and Martin MAREK

Edition

Magnetochemistry, BASEL, SWITZERLAND, MDPI, 2023, 2312-7481

Other information

Language

English

Type of outcome

Article in a journal

Field of Study

20505 Composites

Country of publisher

Switzerland

Confidentiality degree

is not subject to a state or trade secret

References:

Impact factor

Impact factor: 2.600

Marked to be transferred to RIV

Yes

RIV identification code

RIV/75081431:_____/23:00002624

Organization unit

Institute of Technology and Business in České Budějovice

EID Scopus

Keywords (in Czech)

3D tisk; FEM simulace; FFF; hematit; magnetické vlastnosti; magnetit; PLA

Keywords in English

3D printing; FEM simulation; FFF; hematite; magnetic properties; magnetite; PLA

Tags

Changed: 9/1/2024 12:34, Barbora Kroupová

Abstract

In the original language

This work aims to characterize 3D-printed structures composed of a thermoplastic material (polylactic acid (PLA)) containing a combination of magnetic particles composed of iron(III) oxide (hematite) and iron(II)-iron (III) oxide (magnetite) with various infill densities and print orientations in regard to their possible processing by Fused Filament Fabrication additive technology. The correct processing temperatures have been determined using thermal analysis, and the paramagnetic and mechanical properties of the samples have been tested. The relative permeability has been identified to be strongly dependent on the topology parameters of the tested samples. The results of the inductance values for the samples without magnetic additives (infill densities 50% and 100%) have been detected to be comparable; nonetheless, the magnetic samples with 100% infill density has been found to be about 50% higher. A similar trend has been observed in the case of the values of the relative permeability, where the magnetic samples with 100% infill density have been measured as having an about 40% increased relative permeability in the comparison with the samples without magnetic additives (infill densities 20-100%). Finite Element Modelling (FEM) simulations have been applied to determine the magnetic field distributions and, moreover, to calculate the holding forces of all the printed samples. The maximum value of the holding force for the minimum distance of the plastic plate has been found to reach a value of almost 300 N (magnetic sample with 100% infill density). The obtained comprehensive characterization of the printed samples may be utilized for designing and tuning the desired properties of the samples needed in various industrial applications.

In Czech

Cílem této práce je charakterizovat 3D tištěné struktury složené z termoplastického materiálu (kyselina polymléčná (PLA)) obsahujícího kombinaci magnetických částic složených z oxidu železa (III) (hematitu) a oxidu železa (II)-železa (III) (magnetitu) s různou hustotou výplně a orientací tisku s ohledem na jejich možné zpracování aditivní technologií Fused Filament Fabrication. Pomocí termické analýzy byly stanoveny správné teploty zpracování a byly testovány paramagnetické a mechanické vlastnosti vzorků. Bylo zjištěno, že relativní permeabilita je silně závislá na topologických parametrech testovaných vzorků. Byly zjištěny srovnatelné výsledky hodnot indukčnosti u vzorků bez magnetických přísad (hustota výplně 50 % a 100 %), nicméně u magnetických vzorků se 100% hustotou výplně byla zjištěna přibližně o 50 % vyšší hodnota. Podobný trend byl pozorován i v případě hodnot relativní permeability, kdy byla u magnetických vzorků se 100% hustotou výplně naměřena přibližně o 40 % vyšší relativní permeabilita ve srovnání se vzorky bez magnetických přísad (hustota výplně 20-100 %). Simulace metodou konečných prvků (MKP) byly použity k určení rozložení magnetického pole a navíc k výpočtu přídržných sil všech tištěných vzorků. Bylo zjištěno, že maximální hodnota přídržné síly pro minimální vzdálenost plastové desky dosahuje hodnoty téměř 300 N (magnetický vzorek se 100% hustotou výplně). Získané komplexní charakteristiky tištěných vzorků lze využít pro návrh a ladění požadovaných vlastností vzorků potřebných v různých průmyslových aplikacích.

Files attached

magnetochemistry-09-00232.pdf
Request the author's version of the file