2024
Design of Conformal Cooling of an Additively Printed Aluminium Die-Casting Mold Component
SVIŽELOVÁ, Jana; Ladislav SOCHA; Adnan MOHAMED; Martin PINTA; Kamil KOZA et al.Basic information
Original name
Design of Conformal Cooling of an Additively Printed Aluminium Die-Casting Mold Component
Name in Czech
Návrh konformního chlazení aditivně tištěné části formy pro tlakové lití hliníku
Authors
SVIŽELOVÁ, Jana; Ladislav SOCHA; Adnan MOHAMED; Martin PINTA; Kamil KOZA; Tomáš SELLNER; Karel GRYC; M. DVOŘÁK and Miloslav ROH
Edition
ARCHIVES OF FOUNDRY ENGINEERING, WARSZAWA, POLAND, POLSKA AKAD NAUK, 2024, 1897-3310
Other information
Language
English
Type of outcome
Article in a journal
Field of Study
20500 2.5 Materials engineering
Country of publisher
Poland
Confidentiality degree
is not subject to a state or trade secret
References:
Impact factor
Impact factor: 0.600
Marked to be transferred to RIV
Yes
RIV identification code
RIV/75081431:_____/24:00002819
Organization unit
Institute of Technology and Business in České Budějovice
UT WoS
Keywords (in Czech)
Vysokotlaké lití; konformní chlazení; teplotní pole; numerická simulace; návrh formy
Keywords in English
HPDC; Conformal cooling; Temperature field; Numerical simulation; Mold design
Links
FW03010609, research and development project.
Changed: 2/4/2025 14:32, Ing. Barbora Langšádlová
In the original language
The paper describes the design of conformal cooling of an aluminium die-casting mold component using numerical simulations along with validation under industrial conditions. The subject of modifications was the insert. The insert comes into direct contact with the metal during the filling of the mold and solidification of the casting and determines the internal shape of the casting. The aim was to optimize the operating temperatures of the insert, reduce thermal stress in the most exposed area, achieve a more even distribution of temperatures in its volume, and maintain the casting quality. Shape modifications were made by topology optimization to reduce the volume of the insert and achieve material savings. 3D printing was chosen as the production technology due to the wider possibilities regarding the variability of the shape of the internal cooling channels. Three geometric designs of the insert were created, and numerical simulations of the temperature field of the mold were carried out in ProCAST software for each variant. Numerical simulations were validated through the temperature field of the mold detected by a thermal camera during the casting cycle. Based on the results, the final design D was selected, for which a complete numerical simulation was performed, including the filling and solidification of the castings. The results were compared with the original variant A. By adjusting the cooling, temperatures were reduced in the most temperature-exposed area of the insert. The new insert variant D showed higher temperatures in the rest of the volume, resulting from material volume reduction. However, the temperatures became even, and the temperature gradients that existed in the original insert variant A were reduced. The simulation also showed that changes in the temperature field of variant D will not negatively affect the quality of the castings. The component will be manufactured and tested in operational conditions in the next research phase.
In Czech
Článek popisuje návrh konformního chlazení součásti formy pro tlakové lití hliníku pomocí numerických simulací spolu s ověřením v průmyslových podmínkách. Předmětem úprav byla vložka. Vložka přichází do přímého kontaktu s kovem během plnění formy a tuhnutí odlitku a určuje vnitřní tvar odlitku. Cílem bylo optimalizovat provozní teploty vložky, snížit tepelné napětí v nejvíce exponované oblasti, dosáhnout rovnoměrnějšího rozložení teplot v jejím objemu a zachovat kvalitu odlitku. Úpravy tvaru byly provedeny optimalizací topologie, aby se zmenšil objem vložky a dosáhlo se úspory materiálu. Jako výrobní technologie byl zvolen 3D tisk vzhledem k širším možnostem, pokud jde o variabilitu tvaru vnitřních chladicích kanálků. Byly vytvořeny tři geometrické návrhy vložky a pro každou variantu byly provedeny numerické simulace teplotního pole formy v softwaru ProCAST. Numerické simulace byly ověřeny prostřednictvím teplotního pole formy zjištěného termokamerou během licího cyklu. Na základě výsledků byl vybrán konečný návrh D, pro který byla provedena kompletní numerická simulace včetně plnění a tuhnutí odlitků. Výsledky byly porovnány s původní variantou A. Úpravou chlazení došlo ke snížení teplot v teplotně nejexponovanější oblasti vložky. Nová varianta vložky D vykazovala vyšší teploty ve zbytku objemu, což bylo důsledkem snížení objemu materiálu. Teploty se však vyrovnaly a teplotní gradienty, které existovaly v původní variantě vložky A, se snížily. Simulace také ukázala, že změny teplotního pole varianty D nebudou mít negativní vliv na kvalitu odlitků. V další fázi výzkumu bude součást vyrobena a testována v provozních podmínkách.