J 2024

Design of Conformal Cooling of an Additively Printed Aluminium Die-Casting Mold Component

SVIŽELOVÁ, Jana; Ladislav SOCHA; Adnan MOHAMED; Martin PINTA; Kamil KOZA et al.

Základní údaje

Originální název

Design of Conformal Cooling of an Additively Printed Aluminium Die-Casting Mold Component

Název česky

Návrh konformního chlazení aditivně tištěné části formy pro tlakové lití hliníku

Autoři

SVIŽELOVÁ, Jana; Ladislav SOCHA; Adnan MOHAMED; Martin PINTA; Kamil KOZA; Tomáš SELLNER; Karel GRYC; M. DVOŘÁK a Miloslav ROH

Vydání

ARCHIVES OF FOUNDRY ENGINEERING, WARSZAWA, POLAND, POLSKA AKAD NAUK, 2024, 1897-3310

Další údaje

Jazyk

angličtina

Typ výsledku

Článek v odborném periodiku

Obor

20500 2.5 Materials engineering

Stát vydavatele

Polsko

Utajení

není předmětem státního či obchodního tajemství

Odkazy

Impakt faktor

Impact factor: 0.600

Označené pro přenos do RIV

Ano

Kód RIV

RIV/75081431:_____/24:00002819

Organizační jednotka

Vysoká škola technická a ekonomická v Českých Budějovicích

Klíčová slova česky

Vysokotlaké lití; konformní chlazení; teplotní pole; numerická simulace; návrh formy

Klíčová slova anglicky

HPDC; Conformal cooling; Temperature field; Numerical simulation; Mold design

Návaznosti

FW03010609, projekt VaV.
Změněno: 2. 4. 2025 14:32, Ing. Barbora Langšádlová

Anotace

V originále

The paper describes the design of conformal cooling of an aluminium die-casting mold component using numerical simulations along with validation under industrial conditions. The subject of modifications was the insert. The insert comes into direct contact with the metal during the filling of the mold and solidification of the casting and determines the internal shape of the casting. The aim was to optimize the operating temperatures of the insert, reduce thermal stress in the most exposed area, achieve a more even distribution of temperatures in its volume, and maintain the casting quality. Shape modifications were made by topology optimization to reduce the volume of the insert and achieve material savings. 3D printing was chosen as the production technology due to the wider possibilities regarding the variability of the shape of the internal cooling channels. Three geometric designs of the insert were created, and numerical simulations of the temperature field of the mold were carried out in ProCAST software for each variant. Numerical simulations were validated through the temperature field of the mold detected by a thermal camera during the casting cycle. Based on the results, the final design D was selected, for which a complete numerical simulation was performed, including the filling and solidification of the castings. The results were compared with the original variant A. By adjusting the cooling, temperatures were reduced in the most temperature-exposed area of the insert. The new insert variant D showed higher temperatures in the rest of the volume, resulting from material volume reduction. However, the temperatures became even, and the temperature gradients that existed in the original insert variant A were reduced. The simulation also showed that changes in the temperature field of variant D will not negatively affect the quality of the castings. The component will be manufactured and tested in operational conditions in the next research phase.

Česky

Článek popisuje návrh konformního chlazení součásti formy pro tlakové lití hliníku pomocí numerických simulací spolu s ověřením v průmyslových podmínkách. Předmětem úprav byla vložka. Vložka přichází do přímého kontaktu s kovem během plnění formy a tuhnutí odlitku a určuje vnitřní tvar odlitku. Cílem bylo optimalizovat provozní teploty vložky, snížit tepelné napětí v nejvíce exponované oblasti, dosáhnout rovnoměrnějšího rozložení teplot v jejím objemu a zachovat kvalitu odlitku. Úpravy tvaru byly provedeny optimalizací topologie, aby se zmenšil objem vložky a dosáhlo se úspory materiálu. Jako výrobní technologie byl zvolen 3D tisk vzhledem k širším možnostem, pokud jde o variabilitu tvaru vnitřních chladicích kanálků. Byly vytvořeny tři geometrické návrhy vložky a pro každou variantu byly provedeny numerické simulace teplotního pole formy v softwaru ProCAST. Numerické simulace byly ověřeny prostřednictvím teplotního pole formy zjištěného termokamerou během licího cyklu. Na základě výsledků byl vybrán konečný návrh D, pro který byla provedena kompletní numerická simulace včetně plnění a tuhnutí odlitků. Výsledky byly porovnány s původní variantou A. Úpravou chlazení došlo ke snížení teplot v teplotně nejexponovanější oblasti vložky. Nová varianta vložky D vykazovala vyšší teploty ve zbytku objemu, což bylo důsledkem snížení objemu materiálu. Teploty se však vyrovnaly a teplotní gradienty, které existovaly v původní variantě vložky A, se snížily. Simulace také ukázala, že změny teplotního pole varianty D nebudou mít negativní vliv na kvalitu odlitků. V další fázi výzkumu bude součást vyrobena a testována v provozních podmínkách.

Přiložené soubory

Design_of_Conformal_Cooling_of_an_Additively_Printed_Aluminium_Die-Casting_Mold_Component.pdf
Požádat o autorskou verzi souboru