M., Tupaj, Trytek A., Łysiak K., Zbyrad-Kołodziej W., Łaczek A. and Ján MAJERNÍK. The use of concentrated heat stream to repair AlZn10Si8Mg alloy castings. Manufacturing Technology. Usti nad Labem: J. E. Purkyne University in Usti nad Labem, 2020, Volume 20, No 3, p. 401-408. ISSN 1213-2489. Available from: https://dx.doi.org/10.21062/mft.2020.027.
Other formats:   BibTeX LaTeX RIS
Basic information
Original name The use of concentrated heat stream to repair AlZn10Si8Mg alloy castings
Name in Czech Použití koncentrovaného proudu tepla k opravě odlitků ze slitin AlZn10Si8Mg
Authors M., Tupaj (616 Poland, guarantor), Trytek A. (616 Poland), Łysiak K. (616 Poland), Zbyrad-Kołodziej W. (616 Poland), Łaczek A. (616 Poland) and Ján MAJERNÍK (703 Slovakia, belonging to the institution).
Edition Manufacturing Technology, Usti nad Labem, J. E. Purkyne University in Usti nad Labem, 2020, 1213-2489.
Other information
Original language English
Type of outcome Article in a journal
Field of Study 20300 2.3 Mechanical engineering
Country of publisher Czech Republic
Confidentiality degree is not subject to a state or trade secret
WWW URL
RIV identification code RIV/75081431:_____/20:00001807
Organization unit Institute of Technology and Business in České Budějovice
Doi http://dx.doi.org/10.21062/mft.2020.027
Keywords (in Czech) Al slitina; Počítačová tomografie; Koncentrovaný proud tepla; Vady odlitků; Metalografické testy
Keywords in English Al alloy; Computer tomography; Concentrated heat stream; Defects in castings; Metallographic tests
Tags RIV20, SCOPUS, TLK
Changed by Changed by: Kateřina Nygrýnová, učo 23736. Changed: 6/10/2020 11:19.
Abstract
The present paper discusses the possibility to use three different sources of concentrated heat stream to repair superficial defects on AlZn10Si8Mg alloy castings. Simulated defects were prepared on specimens taken from a production casting made with the use of low-pressure casting method. The energy sources used to repair the defect were those known as MIG/MAG, TIG, and ML (micro-laser) methods. As the filler, a AlSi5 welding wire was used. The quality of repair was assessed based on both destructive and non-destructive testing. To evaluate porosity of the performed overlay welds, the computer X-ray tomography technique was employed. Metallographic examination was used to assess macro-and micro-structure of overlay welds, measure geometrical parameters of the welds and the heat-affected zone, and determine values of SDAS microstructure parameter. Hardness of overlay welds and the casting material was measured with the use of Brinell hardness machine.
Abstract (in Czech)
Tato práce pojednává o možnosti použít tři různé zdroje koncentrovaného proudu tepla k opravě povrchových defektů na slitinových odlitcích AlZn10Si8Mg. Simulované vady byly připraveny na vzorcích odebraných z výrobního odlitku vyrobeného metodou nízkotlakého odlévání. K opravě defektu byly použity zdroje energie známé jako metody MIG / MAG, TIG a ML (mikro-laser). Jako plnivo byl použit svařovací drát AlSi5. Kvalita opravy byla hodnocena na základě destruktivního i nedestruktivního testování. K vyhodnocení pórovitosti provedených svarových svarů byla použita technika počítačové rentgenové tomografie. Metalografické vyšetření bylo použito k posouzení makrostruktury a mikrostruktury svarů, měření geometrických parametrů svarů a tepelně ovlivněné zóny a stanovení hodnot parametru mikrostruktury SDAS. Tvrdost svarů a odlévaného materiálu byla měřena pomocí tvrdoměru Brinell.
PrintDisplayed: 25/4/2024 17:40