J 2019

Influence of runner geometry on the gas entrapment in volume of pressure die cast

MAJERNÍK, Ján and Martin PODAŘIL

Basic information

Original name

Influence of runner geometry on the gas entrapment in volume of pressure die cast

Name in Czech

Vliv geometrie vtokového kanálu na zachycení plynu v objemu tlakového odlitku

Authors

MAJERNÍK, Ján and Martin PODAŘIL

Edition

Archives of Foundry Engineering, Warszawa, Polish Academy of Sciences, 2019, 1897-3310

Other information

Language

English

Type of outcome

Article in a journal

Field of Study

20301 Mechanical engineering

Country of publisher

Poland

Confidentiality degree

is not subject to a state or trade secret

References:

Marked to be transferred to RIV

Yes

RIV identification code

RIV/75081431:_____/19:00001591

Organization unit

Institute of Technology and Business in České Budějovice

EID Scopus

Keywords (in Czech)

HPDC; zachycení vzduchu; vývoj produktů; rozměry vtokového kanála; proudění taveniny

Keywords in English

HPDC; Air entrapment; Product development; Runner dimensions; Melt flow

Tags

Changed: 22/4/2020 14:52, Mgr. Milada Šanderová

Abstract

In the original language

The high pressure die casting technology allows the production of complex casts with good mechanical properties, with high production repeatability within narrow tolerance limits. However, the casts are somewhat porous, which may reduce their mechanical properties. There are several recommendations for reducing the porosity of casts, which are aimed at setting the technological parameters of the casting cycle. One of the primary and important ways to reduce the porosity and air entrapment in the melt is a suitable gating system design. Submitted contribution is devoted to assessing the influence of the runner branching geometry on the air entrapment within the cast volume during the filling phase of the casting cycle. Four variants of the gating system for a particular cast are compared with different design of main runner branching. The initial design is based on a real gating system where the secondary runner is connected to the main runner at an angle of 90 °. The modified designs are provided with a continuous transition of the main runner into the secondary ones, with the change in the branching runner radius r1 = 15 mm, r2 = 25 mm and r3 = 35 mm. The air entrapment in the melt is assessed within the cast volume behind the cores, which have been evaluated as a critical points with respect to further mechanical treatment. When designing the structural modification of geometry it was assumed that by branch changing using the radius value r3 = 35 mm, the melt flows fluently, and thus the value of the entrapped air in the volume of the cast will be the lowest. This assumption was disproved. The lowest values of entrapped air in the melt were found in the casts with runner transition designed with radius r1 = 15 mm. The conclusion of the contribution explains the causes of this phenomenon and from a designing point of view it presents proposal for measures to reduce the entrapment of the air in casts

In Czech

Technologie lití kovů pod tlakem umožňuje výrobu tvarově složitých odlitků s dobrými mechanickými vlastnostmi, s vysokou opakovatelností výroby v úzkých tolerančních mezích. Odlitky jsou však do jisté míry pórovité, což může snižovat jejich mechanické vlastnosti. Existuje několik doporučení na snížení porezity odlitků, které jsou zaměřeny na nastavení technologických parametrů licího cyklu. Jako jedna z prvořadých a významných cest ke snižování porezity a ulpívání vzduchu v tavenině se ukazuje vhodný návrh vtokového systému. Předkládaný článek je věnován posouzení dopadů geometrie větvení vtokového kanálu na zachycování vzduchu v objemu odlitku během plnicí fáze licího cyklu. Jsou porovnávány čtyři varianty vtokové soustavy pro konkrétní odlitek s různým konstrukčním řešením větvení hlavního vtokového kanálu. Prvotní konstrukční řešení vychází z reálné vtokové soustavy, kdy je vedlejší vtokový kanál napojen na hlavní kanál pod úhlem 90 °. Modifikované konstrukční řešení jsou opatřeny plynulým přechodem hlavního vtokového kanálu ve vedlejší, se změnou poloměru větvení kanálů r1 = 15 mm, r2 = 25 mm a r3 = 35 mm. Zachycení vzduchu v tavenině je posuzováno v objemu odlitků za jádry, které byly s ohledem na další mechanické opracování vyhodnoceny jako kritická místa. Při návrhu konstrukčních modifikaci geometrie se předpokládalo, že při změně větvení využitím hodnoty poloměru r3 = 35 mm tavenina proudí plynule, a tedy i hodnota zachycení vzduchu v objemu odlitku bude nejnižší. Tento předpoklad byl vyvrácen. Nejnižší hodnoty zachyceného vzduchu v tavenině vykazovaly odlitky s přechodem kanálů navrženým s poloměrem r1 = 15 mm. Závěr článku vysvětluje příčiny tohoto jevu a z konstrukčního hlediska prezentuje návrhy opatření pro snižování zachycení vzduchu v odlitcích.

Files attached