J 2019

Evaluation of the Temperature Distribution of a Die Casting Mold of X38CrMoV5_1 Steel

MAJERNÍK, Ján and Martin PODAŘIL

Basic information

Original name

Evaluation of the Temperature Distribution of a Die Casting Mold of X38CrMoV5_1 Steel

Name in Czech

Vyhodnocení distribuce teploty v tlakové licí formě z oceli X38CrMoV5_1

Authors

MAJERNÍK, Ján and Martin PODAŘIL

Edition

Archives of Foundry Engineering, Warszawa, POLSKA AKAD NAUK, POLISH ACAD SCIENCES, PL DEFILAD 1, 2019, 1897-3310

Other information

Language

English

Type of outcome

Article in a journal

Field of Study

20301 Mechanical engineering

Country of publisher

Poland

Confidentiality degree

is not subject to a state or trade secret

References:

Marked to be transferred to RIV

Yes

RIV identification code

RIV/75081431:_____/19:00001543

Organization unit

Institute of Technology and Business in České Budějovice

EID Scopus

Keywords (in Czech)

Vývoj produktu; simulace procesu odlévání; distribuce teploty; materiál formy; temperování

Keywords in English

High Pressure Die Casting; Runner; Construction; Technological Parameters

Tags

Changed: 22/4/2020 14:44, Mgr. Blanka Mikšíková

Abstract

In the original language

Relatively cold die material comes into contact with the substantially higher temperature melt during the casting cycle, causing high thermal fluctuations resulting into the cyclic thermal stress. The presented contribution is devoted to the assessment of the impact of temperature distribution on individual zones in the die volume. The evaluated parameter is the die temperature. It was monitored at two selected locations with the 1 mm, 2 mm, 5 mm, 10 mm and 20 mm spacing from the die cavity surface to the volume of cover die and ejector die. As a comparative parameter, the melt temperature in the middle of the runner above the measuring point and the melt temperature close to the die face were monitored. Overall, the temperature was monitored in 26 evaluation points. The measurement was performed using the Magmasoft simulation software. The input settings of the casting cycle in the simulation were identical to those in real operation. It was found, that the most heavily stressed die zones by temperature were within the 20 mm from the die face. Above this distance, the heat supplied by the melt passes gradually into the entire die mass without significant temperature fluctuations. To verify the impact of the die cooling on the thermal stress, a tempering system was designed to ensure different heat dissipation conditions in individual locations. At the end of the contribution, the measures proposals to reduce the high thermal stress of dies resulting from the design of the tempering channel are presented. These proposals will be experimentally verified in the following research work.

In Czech

Relativně studený materiál formy přichází při licím cyklu do styku s taveninou s podstatně vyšší teplotou, což způsobuje vysoké tepelné výkyvy, které vyvolávají cyklické teplotní namáhání. Předkládaný článek je věnován posuzování dopadu tohoto namáhání na jednotlivé zóny v objemu formy. Jak vyhodnocován parametr je teplota formy. Teplota byla sledována ve dvou zvolených místech, s rozložením 1mm, 2mm, 5mm, 10mm a 20mm ve směru od povrchu pracovní dutiny formy do objemu pevné a pohyblivé části formy. Jako srovnávací parametr byla sledována teplota taveniny uprostřed vtokového kanálu nad měřicím místem a teplota taveniny těsně u líci formy. Celkově byla teplota sledována v 26 vyhodnocovaných měřicích bodech. Měření bylo provedeno využitím simulačního softwaru Magmasoft. Vstupní nastavení licího cyklu v simulaci byly totožné s nastaveními v reálném provozu. Bylo zjištěno, že tepelně jsou nejvíce namáhány zóny formy ve vzdálenosti do 20mm od líce formy. Nad touto vzdáleností prochází teplo dodané taveninou postupně do celé hmoty formy bez značných teplotních výkyvů. Pro ověření vlivu chlazení formy na tepelné namáhání, byl navržen temperační systém tak, aby zajistil různé podmínky odvodu tepla v jednotlivých místech. V závěru článku jsou prezentovány návrhy opatření pro snížení vysokého teplotního namáhání forem plynoucí z konstrukce temperačních kanálů. Tyto návrhy budou experimentální ověřovány v následujících výzkumných pracích

Files attached

evaluation-of-the-temperature-distribution-of-a-die-casting-mold-of-x38crmov5-1-steel.pdf
Request the author's version of the file