J 2019

Optimization of the Runner Numerical Design Dimensions using the Simulation Program

MAJERNÍK, Ján; Štefan GAŠPÁR; Martin PODAŘIL and Jan KOLÍNSKÝ

Basic information

Original name

Optimization of the Runner Numerical Design Dimensions using the Simulation Program

Name in Czech

Optimalizácia numerického návrhu rozmerov vtokového kanála využitím simulačného programu

Authors

MAJERNÍK, Ján; Štefan GAŠPÁR; Martin PODAŘIL and Jan KOLÍNSKÝ

Edition

Manufacturing technology, Ústí nad Labem, J.E. Purkyně university in Usti nad Labem, 2019, 1213-2489

Other information

Language

English

Type of outcome

Article in a journal

Field of Study

20300 2.3 Mechanical engineering

Country of publisher

Czech Republic

Confidentiality degree

is not subject to a state or trade secret

References:

Marked to be transferred to RIV

Yes

RIV identification code

RIV/75081431:_____/19:00001502

Organization unit

Institute of Technology and Business in České Budějovice

EID Scopus

Keywords (in Czech)

lití kovů pod tlakem; vtokový kanál; konstrukce; technologické parametre

Keywords in English

High Pressure Die Casting; Runner; Construction; Technological Parameters

Tags

Changed: 22/4/2020 14:24, Mgr. Blanka Mikšíková

Abstract

In the original language

The proper design of the gating system including the tempering and venting of the mold significantly influences the final quality of the casting and economize the costs of the foundries. The initial numerical design of the gating system is often sufficient for creating of the documentation for the mold design, but without the practical experi-ence of the designer, it does not reveal the hidden problem emerging from the melt flow through the gating system as well as the temperature and gas mode of the mold.The contribution is dedicated to the optimization of the runner dimensions determined by the numerical calculation. The theoretical part presents the methodology, based on which the gating system was designed for a particular type of the pressure casting. The experimental part is dedicated to the influence of the cross sectional area of the runner on the change of the melt temperature before entering the ingate. It was assumed that the larger runner cross section gives the melt greater volume and heat capacity and thus the melt enters the ingate with the higher temperature. The obtained temperature results are then compared witht he melt flow rate values, based on which an optimal sulotion for the runner design dimensions is determined.

In Czech

Správný návrh vtokového systému, včetně temperace a odvzdušnění formy významnou měrou ovlivňuje výslednou jakost odlitku a šetří ekonomické náklady sléváren. Prvotní numerický návrh vtokových soustav často postačuje k tvorbě dokumentace pro provedení forem, ale bez praktických zkušeností návrháře neodhalí skryté problémy plynoucí z proudění taveniny přes vtokovou soustavu, jako i teplotního a plynového režimu formy. Předkládaný článek je věnován optimalizaci rozměrů vtokového kanálu určených na základě numerického výpočtu. V teoretické části prezentuje metodiku, na jejímž základě byla navržena vtoková soustava pro konkrétní typ tlakového odlitku. V experimentální části je zkoumán vliv plochy průřezu vedlejšího kanálu na změnu teploty taveniny před vstupem do vtokového zářezu. Vycházelo se z předpokladu, že větší průřez vtokového kanálu udává tavenině vyšší objem a tepelnou kapacitu, a tedy tavenina vstupuje do vtokového zářezu i s vyšší teplotou. Získané výsledky pro teplotu jsou následně v komparaci s hodnotami rychlostí proudu taveniny, na jejich základě je určeno optimální řešení návrhu rozměrů vtokového kanálu.

Files attached